P18 EUROPE STANDARD 200KHZ 10A/100A DOUBLE RANGE SPLIT CORE CLAMP ON CT
INTRODUCE
The round jaw design on the P18 series double range clamp on ct along with the high content permalloy core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency ~200kHz are important. Measurement range is 1mA to 200A. for example 10A/100A, 20A/200A range.
The P18 clamp on ct is a general purpose 200A AC current clamp probe designed for use with DMMs, power loggers and energy meter calibration instruments that have a current input. It has a 1000:1 or 2000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The P18 clamp ct has an integral 2.5m lead terminated. The rounded jaw design on this current clamp makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important. It can as one high precision clamp on currrent transformer for metering device.
All of our clamp on cts are strictly comply IEC60044-1, IEC 61869-2, ANSI/IEEE C57.13, GB1208-2006, GB/T 20840.1-2010, GB/T 20840.2-2014, GB/T 22071.1-2018, IEC/EN61010-2-032, IEC/EN 61010-2-031.
FEATURES
IEC/EN61010-2-032, IEC/EN 61010-2-031, IEC 61869-2 etc standard; Measurement range of 1mA to 240A AC; Low phase shift for power measurement; High precision 0.1% for current measurement; Frequency 10Hz-2MHz bandwidth; Holding wire diameter: φ18mm; 128 times harmonic measurement; Improved ergonomic design & easy operation; High content permalloy core; Double range 10A/100A or 20A/200A design; Conforms to EN 61010, 600V CAT III; Large jaw opening accommodates conductors up to two 500kcoil; Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters; UL, CE mark; As a high accuracy clamp current transformer;
APPLIATIONS
Electricity meter calibrator;
Power quality analyzer(PQA);
Phase angle meter;
Earth resistance meter;
Measuring around cable bundles;
Power load monitoring;
Data logging/recording;
Large industrial loads;
Power and harmonic meters;
Power quality monitoring;
CT secondary current detection;
Oscilloscopes;
Multimeter;
Energy sub-meters;
Power meter;
Waveform analysis;
PARAMETERS
| Electrical parameters | |
|---|---|
| Ratio | 1000:1, 2000:1, 2500:1, 4000:1 (customized) |
| Accuracy Class | 0.1%, 0.2% |
| Primary current | 0-100A AC, 0-200A AC |
| Signal output | 1mA/A, 1mV/A, 10mV/A, 100mV/A |
| Secondary voltage | 0-100mV AC, 0-1V AC, 0-5V AC; |
| Secondary current | 0-40mA, 0-100mA or 0-200mA AC |
| Max. Cont. Input current | 120A or 240A |
| Load capacity | ≤20Ω, standard 4Ω |
| Over voltage category | CAT III 600V |
| Frequency range | 10Hz-2MHz |
| Dielectric strength | 3KV 50Hz/60Hz at 1minute |
| Temperature range | -40°C to +55°C |
| Output | 2.5 meter cable with D01 or BNC connector |
| Max. voltage not insulated conductors | 720V |
| Standard | EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III |
| Installation | Clamp type |
| Range | 10A, 20A, 100A, 200A optional |
| Output mode | Lead output(2.5m) |
| Output signal | 333mV, 500mV, 1V, 2V, 5V AC at nominal input current |
| Connector | BNC, 4mm banana, signal cable(2 cores), customized |
| Accuracy(100A/200A Range) | |
| 0-1A | ≤0.5% |
| 1-10A | ≤0.2% |
| 10-200A | ≤0.1% |
| Phase Shift(100A/200A Range) | |
| 0-1A | ≤0.5° |
| 1-10A | ≤0.2° |
| 10-200A | ≤0.1° |
| Mechanical parameters | |
| Dimensions (L x W x H) (mm) | 52.5 x 137 x 28 |
| Weight (g) | 400 |
| Holding wire diameter (mm) | φ18 |
| Max. jaw opening (mm) | 18 |
| Jaw color | Red, yellow, blue, green, black |
| Material | PC+ABS, UL94 V0 |
SELECTION GUIDE
| Model | Rate Current | Max Current | Secondary Current | Coil Ratio | Burden Resistance | Accuracy |
|---|---|---|---|---|---|---|
| P18-5 | 5A | 6A | 5mA | 1000:1 | customized | 0.1% |
| P18-10 | 10A | 12A | 10mA | 1000:1 | customized | 0.1% |
| P18-20 | 20A | 24A | 20mA | 1000:1 | customized | 0.1% |
| P18-100 | 100A | 120A | 100mA | 1000:1 | customized | 0.1% |
| P18-200 | 200A | 240A | 200mA | 1000:1 | customized | 0.1% |
| P18-10-2 | 10A | 12A | 10mA | 1000:1 | customized | 0.2% |
| P18-20-2 | 20A | 24A | 20mA | 1000:1 | customized | 0.2% |
| P18-100-2 | 100A | 120A | 100mA | 1000:1 | customized | 0.2% |
| P18-200-2 | 200A | 240A | 200mA | 1000:1 | customized | 0.2% |
| P18-5 | 5A | 6A | 2.5mA | 2000:1 | customized | 0.1% |
| P18-10 | 10A | 12A | 5mA | 2000:1 | customized | 0.1% |
| P18-20 | 20A | 24A | 10mA | 2000:1 | customized | 0.1% |
| P18-100 | 100A | 120A | 50mA | 2000:1 | customized | 0.1% |
| P18-200 | 200A | 240A | 100mA | 2000:1 | customized | 0.1% |
| P18-10-2 | 5A | 6A | 2.5mA | 2000:1 | customized | 0.2% |
| P18-10-2 | 10A | 12A | 5mA | 2000:1 | customized | 0.2% |
| P18-20-2 | 20A | 24A | 10mA | 2000:1 | customized | 0.2% |
| P18-100-2 | 100A | 120A | 50mA | 2000:1 | customized | 0.2% |
| P18-200-2 | 200A | 240A | 100mA | 2000:1 | customized | 0.2% |
| P18-10 | 10A | 12A | 2.5mA | 4000:1 | customized | 0.1% |
| P18-20 | 20A | 24A | 5mA | 4000:1 | customized | 0.1% |
| P18-100 | 100A | 120A | 25mA | 4000:1 | customized | 0.1% |
| P18-200 | 200A | 240A | 50mA | 4000:1 | customized | 0.1% |
| P18-10-2 | 10A | 12A | 2.5mA | 4000:1 | customized | 0.2% |
| P18-20-2 | 20A | 24A | 5mA | 4000:1 | customized | 0.2% |
| P18-100-2 | 100A | 120A | 25mA | 4000:1 | customized | 0.2% |
| P18-200-2 | 200A | 240A | 50mA | 4000:1 | customized | 0.2% |
| Model | Rate Current | Max Current | Secondary Voltage | Coil Ratio | Burden Resistance | Accuracy |
| P18V1-100 | 100A | 120A | 1V | 1000:1 | customized | 0.1% |
| P18V2-100 | 100A | 120A | 2V | 1000:1 | customized | 0.1% |
| P18V5-100 | 100A | 120A | 5V | 1000:1 | customized | 0.1% |
| P18V10-100 | 100A | 120A | 10V | 1000:1 | customized | 0.1% |
| P18V1-200 | 200A | 240A | 1V | 1000:1 | customized | 0.1% |
| P18V2-200 | 200A | 240A | 2V | 1000:1 | customized | 0.1% |
| P18V5-200 | 200A | 240A | 5V | 1000:1 | customized | 0.1% |
| P18V1-100-2 | 100A | 120A | 1V | 1000:1 | customized | 0.2% |
| P18V2-100-2 | 100A | 120A | 2V | 1000:1 | customized | 0.2% |
| P18V5-100-2 | 100A | 120A | 5V | 1000:1 | customized | 0.2% |
| P18V10-100-2 | 100A | 120A | 10V | 1000:1 | customized | 0.2% |
| P18V1-200-2 | 200A | 240A | 1V | 1000:1 | customized | 0.2% |
| P18V2-200-2 | 200A | 240A | 2V | 1000:1 | customized | 0.2% |
| P18V5-200-2 | 200A | 240A | 5V | 1000:1 | customized | 0.2% |
| P18V1-100-D | 10A/100A | 12A/120A | 1V | 1000:1 | customized | 0.1% |
| P18V2-200-D | 20A/200A | 24A/240A | 2V | 1000:1 | customized | 0.1% |
| Notes: Can be customized clamp on current transformers according to user requirements! | ||||||
CLAMP ON CURRENT TRANSFORMER SELECTION MODEL
| Model | Current Range | Max Current | Secondary Output Signal | Ratio | Resistance | Accuracy |
|---|---|---|---|---|---|---|
| S50 | 0-1200A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| S120 | 0-3000A | 3600A | 250mA, 500mA, 1A, 2A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P8 | 0-10A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P18 | 0-200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P50 | 0-1000A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P110 | 0-1500A | 1500A | 250mA, 500mA, 1A, 2A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q8A1 | 20A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q8A2 | 20A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q13 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q20A | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q20B | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q40 | 500A | 600A | 200mA, 250mA, 500mA, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q50A | 1000A | 1000A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q70 | 1000A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q110 | 1500A | 1500A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q125 | 2000A | 2400A | 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| Q125B | 3000A | 3600A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| Q150 | 3000A | 3600A | 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| XQ13 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| XQ20 | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| HQ15 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
