P110 HIGH ACCURACY 1000A CABLE FAULT ANALYSIS CURRENT TRANSFORMER CLAMP
INTRODUCE
The P110 is a high performance AC current transformer clamp with excellent transformation and low phase shift. The high quality magnetic permalloy core and uniform windings provide for accurate measurements up to 1000AAC/600AAC/250AAC. The "ring type" jaw permits good magnetic conduction and cable positionings. Provide excellent RMS capabilities and reliable signal reproduction. It is well suited for power quality applications where high accuracy and low phase shift along with wide frequency from 10Hz to 2MHz are important. Measurement range is 1mA to 1200A. The P110 CT clamp is a general purpose 1000A AC current probe designed for use with DMMs, cable fault analysis and loggers instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The P110 current transformer clamp has an integral 2.5m or 5m lead terminated. The rounded jaw design on this probe makes it well-suited for cable fault analysis applications where high accuracy and low phase shift and wide frequency.
All of our current transformer clamp are strictly comply IEC60044-1, IEC 61869-2, ANSI/IEEE C57.13, GB1208-2006, GB/T 20840.1-2010, GB/T 20840.2-2014, GB/T 22071.1-2018, IEC/EN61010-2-032, IEC/EN 61010-2-031.
FEATURES
APPLIATIONS
Cable fault analysis;
Power quality analyzer(PQA);
Power and harmonic meters;
Measuring around cable bundles;
Power load monitoring;
Earth resistance meter;
Large industrial loads;
Waveform analysis;
Leakage current meter;
Energy meter calibrator;
Oscilloscopes meter;
Multimeter;
Digital multi-meter;
Multi-function energy meter;
PARAMETERS
| Electrical parameters | |
|---|---|
| Ratio | 1000:5, 1000:1, 2000:1, 4000:1 (customized) |
| Accuracy Class | 0.1%, 0.2%, 0.5%, 1% |
| Primary current | 0-1000A AC, 0-500A AC, 0-200A AC, 0-100A AC |
| Signal output | 1mA/A, 5mA/A, 1mV/A, 5mV/A, 10mV/A |
| Secondary voltage | 0-333mV, 0-500mV, 0-1V, 0-5V, 0-10V AC; |
| Secondary current | 0-250mA, 0-500mA, 0-1A or 0-5A AC |
| Max. Cont. Input current | 1500A |
| Load capacity | ≤20Ω, standard 4Ω |
| Over voltage category | CAT III 600V |
| Frequency range | 10Hz-2MHz |
| Dielectric strength | 33KV 50Hz/60Hz at 1minute |
| Temperature range | -20°C to +55°C |
| Output | 2.5 meter cable with D01 or BNC connector |
| Max. voltage not insulated conductors | 720 V |
| Standard | EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III |
| Installation | Clamp type |
| Range | 100A, 200A, 400A, 500A, 600A, 1000A optional |
| Output mode | Lead output(2.5m, 5m, 10m or customized) |
| Output signal | 333mV, 500mV, 1V, 2V, 5V, 10V AC at nominal input current |
| Connector | BNC, 4mm banana, signal cable(2 cores), customized |
| Accuracy (1000A Range) | |
| 0-10A | ≤0.5% |
| 10-100A | ≤0.2% |
| 100-1000A | ≤0.1% |
| Phase Shift(1000A Range) | |
| 0-10A | ≤0.5° |
| 10-100A | ≤0.2° |
| 100-1000A | ≤0.1° |
| Mechanical parameters | |
| Dimensions (L x W x H) (mm) | 163 x 310 x 34 |
| Weight (g) | 900 |
| Holding wire diameter (mm) | φ110 |
| Max. jaw opening (mm) | 110 |
| Jaw color | Black |
| Material | PC+ABS, UL94 V0 |
SELECTION GUIDE
| Model | Rate Current | Max Current | Secondary Current | Coil Ratio | Burden Resistance | Accuracy |
|---|---|---|---|---|---|---|
| P110-500 | 500A | 600A | 5A | 100:1 | 2.5VA | 0.5% |
| P110-600 | 600A | 720A | 5A | 120:1 | 2.5VA | 0.5% |
| P110-800 | 800A | 960A | 5A | 160:1 | 2.5VA | 0.5% |
| P110-1000 | 1000A | 1200A | 5A | 200:1 | 2.5VA | 0.5% |
| P1101-200 | 200A | 240A | 1A | 200:1 | customized | 0.2% |
| P1101-300 | 300A | 360A | 1A | 300:1 | customized | 0.2% |
| P1101-400 | 400A | 480A | 1A | 400:1 | customized | 0.2% |
| P1101-500 | 500A | 600A | 1A | 500:1 | customized | 0.2% |
| P1101-600 | 600A | 720A | 1A | 600:1 | customized | 0.2% |
| P1101-800 | 800A | 960A | 1A | 800:1 | customized | 0.2% |
| P1101-1000 | 1000A | 1200A | 1A | 1000:1 | customized | 0.1% |
| P1102-500 | 500A | 600A | 500mA | 1000:1 | customized | 0.1% |
| P1102-600 | 600A | 720A | 500mA | 1200:1 | customized | 0.1% |
| P1102-800 | 800A | 960A | 500mA | 1500:1 | customized | 0.1% |
| P1102-1000 | 1000A | 1200A | 500mA | 2000:1 | customized | 0.1% |
| P1103-800 | 800A | 960A | 400mA | 2000:1 | customized | 0.1% |
| P1103-1000 | 1000A | 1200A | 400mA | 2500:1 | customized | 0.1% |
| P1104-250 | 250A | 300A | 250mA | 1000:1 | customized | 0.1% |
| P1104-500 | 500A | 600A | 250mA | 2000:1 | customized | 0.1% |
| P1104-1000 | 1000A | 1200A | 250mA | 4000:1 | customized | 0.1% |
| Model | Rate Current | Max Current | Secondary Voltage | Coil Ratio | Burden Resistance | Accuracy |
| P1105-200 | 240A | 1200A | 1V | 1000:1 | customized | 0.1% |
| P1105-200 | 240A | 1200A | 1V | 1000:1 | customized | 0.1% |
| P1105-300 | 300A | 360A | 1V | 1000:1 | customized | 0.1% |
| P1105-400 | 400A | 480A | 1V | 1000:1 | customized | 0.1% |
| P1105-500 | 500A | 600A | 1V | 1000:1 | customized | 0.1% |
| P1105-600 | 600A | 720A | 1V | 1000:1 | customized | 0.1% |
| P1105-800 | 800A | 960A | 1V | 1000:1 | customized | 0.1% |
| P1105-1000 | 1000A | 1200A | 1V | 1000:1 | customized | 0.1% |
| P1106-200 | 200A | 240A | 5V | 1000:1 | customized | 0.1% |
| P1106-300 | 300A | 360A | 5V | 1000:1 | customized | 0.1% |
| P1106-400 | 400A | 480A | 5V | 1000:1 | customized | 0.1% |
| P1106-500 | 500A | 600A | 5V | 1000:1 | customized | 0.1% |
| P1106-600 | 600A | 720A | 5V | 1000:1 | customized | 0.1% |
| P1106-800 | 800A | 960A | 5V | 1000:1 | customized | 0.1% |
| P1106-1000 | 1000A | 1200A | 5V | 1000:1 | customized | 0.1% |
| P1108-200 | 200A | 240A | 10V | 1000:1 | customized | 0.1% |
| P1108-300 | 300A | 360A | 10V | 1000:1 | customized | 0.1% |
| P1108-400 | 400A | 480A | 10V | 1000:1 | customized | 0.1% |
| P1108-500 | 500A | 600A | 10V | 1000:1 | customized | 0.1% |
| P1108-600 | 600A | 720A | 10V | 1000:1 | customized | 0.1% |
| P1108-800 | 800A | 960A | 10V | 1000:1 | customized | 0.1% |
| P1108-1000 | 1000A | 1200A | 10V | 1000:1 | customized | 0.1% |
| Notes: Can be customized clamp on current transformers according to user requirements! | ||||||
CLAMP ON CURRENT TRANSFORMER SELECTION MODEL
| Model | Current Range | Max Current | Secondary Output Signal | Ratio | Resistance | Accuracy |
|---|---|---|---|---|---|---|
| S50 | 0-1200A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| S120 | 0-3000A | 3600A | 250mA, 500mA, 1A, 2A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P8 | 0-10A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P18 | 0-200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P50 | 0-1000A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| P110 | 0-1500A | 1500A | 250mA, 500mA, 1A, 2A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q8A1 | 20A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q8A2 | 20A | 20A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q13 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q20A | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q20B | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q40 | 500A | 600A | 200mA, 250mA, 500mA, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q50A | 1000A | 1000A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q70 | 1000A | 1200A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q110 | 1500A | 1500A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| Q125 | 2000A | 2400A | 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 200:1, 600:1, 1000:1, 2000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| Q125B | 3000A | 3600A | 250mA, 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| Q150 | 3000A | 3600A | 500mA, 1A, 5A, 333mV, 1V, 2V, 5V, 10V etc | 600:1, 1000:1, 2000:1, 4000:1 etc | 2.5VA, 1VA, 4Ω, 10Ω, 20Ω etc | 0.2%, 0.5% |
| XQ13 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| XQ20 | 200A | 240A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V, 10V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
| HQ15 | 100A | 120A | 2mA, 2.5mA, 5mA, 10mA, 20mA, 333mV, 1V, 2V, 5V etc | 1000:1, 2000:1, 2500:1, 4000:1 etc | 4Ω, 10Ω, 20Ω etc | 0.1%, 0.2%, 0.5% |
